XB series cycloid gearbox

XB cycloidal reducer is a mechanical, in accordance with the pinciple of less tooth differenced planetary transmission,cycloid pin gear meshing to realize deceleration.This machine has installation type of horizontal,vertical, biaxial and straight league, widely used in metallurgy, mining, construction, chemical, textile, light industry and other industries preferred equipment.

1.XB cycloidal reducer smooth running, low noise: in operation at the same time contact tooth number, contact ratio is big, smooth operation, overload capacity is strong, vibration and low noise, various specifications of the machine has little noise.

2.Cycloid reducer, reduction ratio, high efficiency: level reduction gear ratio of 9 ~ 87, two-stage reduction gear ratio of 121 to 5133, the multi-stage combination can reach tens of thousands, and needle tooth is the set of type rolling friction, no relative sliding mesh surface, so the reduction gear efficiency up to 94%.

3.The use of reliable, long life: because of the main parts are adopt high carbon alloy steel quenching (HRC58-62), fine grinding and become, again and cycloid and needle teeth meshing transmission to the tooth form rolling friction, friction coefficient is small, the meshing area with no relative sliding, wastage, so durable.

4.Compact structure, small volume, compared with other reducer with power, weight is small in size by more than a third, due to the planetary transmission, the input shaft and output shaft in the same axis, to get the smallest possible size.

Power: 0.37 KW ~ 55 KW
Torque: 150 n · m ~ 20000 n. m
Ratio: single stage: 9-87 ; double stage:121-7569 ; three stage:2057-658503

Platform lifting, working height adjustment of surface processing machine, tilt level adjusting of sliding transmission belt, working height modification of corrector, automatic opening and closing of large scale windows and doors.

Notes before installation:
1.Clean out the shaft and inspect if there is bruising or dirt on the shaft before use the gearbox.
2.Working temperature is 0~40 degree.
3.Check if the mating dimension of hole which connect to the steering gearbox meet the requirements.
4.Please change the stopper to vent plug at the highest position before use the gearbox to ensure the steering gearbox can vent the gas in the body when it running.

Installation:
1.Steering gearbox only can be mounted on flat, vibration-reducing, torsion resist supporting structure.
2. In any case, knocking belt pulley, coupler, small gear or chain wheel by hammer into the output shaft is not allowed to prevent bearing and shaft from damaging.

Operation and maintenance:
1.Please inspect if the steering gearbox is flexible after installation. Please conduct a non-load test before formal using; Add the load gradually under the condition of normal running.
2.Use the steering gearbox at exceeding rated load is forbidden.
3.Check the oil level before and during using the steering gearbox, lubricating oil was already filled into the gearbox before delivery.

Oil change rule:
First time of oil change: after 300-400 hours running. Then change the oil after every 1500-2000 hours.
The lubricating oil should be inspected every half month under the bad working condition and the occasion of high temperature, heavy dust. Please change the oil once dirt is found to keep lubricating oil clean, lengthen steering gearbox service time and increase economic benefit.

1. How to store the gearbox?

1)Keep the reducer in a clean and dry place.

2)If it will be stored outdoor or in a humid place, please put the reducer in a box and packed tightly with plastic bag to avoid the rain and external erosion. ( take measure of anti-condensation and anti-rust)

2. Cautions during operation:

1)Overload is forbidden.

2)Input speed can not exceed the proper max. Speed.

3)Please stop and check the gearbox if there are the following occurs:

Temperature rise suddenly

Abnormal big noise in a sudden

Speed became unstable suddenly

3.Warranty instruction:
The following cost and damages are not included in our warranty:

1)Freight cost
2)If the Reducer connect with or insert in a unit, when we dismounting or mounting on the unit and other extra action, there will be a cost.( this is not contained in the warranty)
3)The indirect damage that user lost the appliance chance or business break off due to reducer breakdown.
4)Other derivative and accompanying damages.